You will need to remove the last deck board from the beam. This board may have more nails than other boards and be difficult to remove; therefore, we cut the nails using the Milwaukee Sawzall with a fine tooth metal blade. This made board removal quick and easy. A long blade will be necessary because of the nails in the intersecting beams
Take a couple rows off first and then take a 6' 2x4 and nail a 2' piece to flat to the 1-1/2" side of it about 1' in looks like a t and lay the 2' piece on the joist and stick the 1-1/2" edge of the 6' 2x4 under the deck board and pry up.It pops right up.
Thankfully, removing an old deck board to replace it is a fairly strhtforward task, which means you can get your deck back to looking like new in no time. Wait for a dry, cool day, if possible. Wood shrinks when it is cold and dry, making the joints between boards larger and easier to fit a pry bar between for leverage.
The only additional step is installing support blocks alongside the joists the horizontal structural members supporting the surface deck boards . This method works well if you don't want to remove and replace the entire board. Alternatively, you can simply remove the old board entirely and replace it with a matching length of new decking board.
Start by removing all railings and stairs, then move on to the deck boards. A majority of decks nowadays are built with screws, which are simple enough to remove with a drill or electric screwdriver. If your deck was built with nails, simply pull out the nails or pry the boards up with a hammer and a pry bar.
To remove old deck stain from the wood you have to use a deck stripper. A quality deck stripper will break up and soften any old stain allowing it to be washed away. Most deck strippers will not remove solid stain or paints if this is the case you may have to sand the old stain to get back down to bare wood again.
This is tricky, because weathered deck boards look alike. Remove a board, cut it with a circular saw, and smell the wood to identify the species. Pressure-treated pine has a sweet smell, cedar an aromatic smell, and redwood a more pungent smell. Ask your lumberyard to cut a scrap from each species and match the smell to your own board.
Now you have a deck board removal tool on one end and a wedge rock breaking tool at the other. Let me also point out the leverage capability of a long bar, especially if you are a tall man. If you are removing deck boards that have been screwed down, this bar will take them off with ease. Bob
The small amount of wood taken out will not matter, but lean the blade toward the wood being discarded. If you can't access the bottom of the deck, you can remove a section of the board to be discarded close to the screw and then cut the screw horizontally. The stub of the old screw in the framing board will be covered by the new boards.
Table of Contents:You Will NeedSteps to Remove the StainAdditional Tips and Advice advertisement Penny asked: How do I remove tree sap from a wooden deck? How would I remove pine tree sap from a wood deck that has already been stained. I am planning to redo the deck by cleaning it and restaining it. Any
You need to be careful in removing the bad boards if you want to salvage the good section for reuse--the wood will split easily. If you can get under the deck, the easy solution is to pound upwards with a block of wood set against the underside of the board you want to remove, driving the block up with a heavy hammer or small sledge at the
Pry the decking joists away from the rim joist, which is the frame that holds the deck joists in place. If the joists are large and hard to remove, pound them loose with a large sledgehammer, and then pry them off.
I need to access under my deck to dig in agi pipes for drainage and the only way is to remove a few rows of boards. Any ideas how to get boards up without damaging them or the joists?
I currently have a deck comprised of barn boards, which needs to be removed. I also used the sawzall to cut the nails at the joist and then set my son to work tapping the short nail end out of the bo
Each year I wind up having to replace a few deck boards that have become cupped on the end, or is starting to split. Because the screw head is sunken beneath the surface of the wood, and the crap that has filled up the hole, it is impossible to see the head of the screw, and most of them are not
Screwed-in-place decking is harder to remove than nailed-down boards are Figure 5 . Most of the time, the boards pull up and leave the screws behind in the joists. About 70 percent of those screws can be removed with a screw gun. The worst, though, are stainless screws, whose heads tend to strip out.
I just had my deck boards replaced on a 12x16 deck with 4ft wide pair of steps. Cost ended up being $1140. My late husband built the deck in 2003 using 1x6 pressure treated deck boards with screws. I had to replace a few boards over the years. Finally had more bad boards so decided to replace all.
This is the easiest way to pry a deck boards that I know of and I wanted to share it with you. If your deck has screws here is a video that will help you to remove the screws. link - www
Allow the wood to fully dry and then sand the deck with fine-grit sandpaper, such as 120- or 150- grit to remove fine specks of paint and to smooth the wood in preparation for a new coat of finish.